To check the IMEI (International Mobile Equipment Identity)
Information you get from the IMEIXXXXXX
XX XXXXXX X
TAC FAC SNR SP
TAC = Type approval code
FAC = Final assembly code
SNR = Serial number
SP = Spare
TO CHECK THE PHONES SOFTWARE REVISION
Information you get from the Software revision-
1ST Line = Software revision
2ND Line = The date of the software release
3RD Line = Phone type
TO ENTER THE SERVICE MENU
Type- *#92702689# (*#WAR0ANTY#)
Serial number (IMEI)
roduction date (MM/YY)
Purchase date (MM/YY) You can only enter the date once.
Date of last repair (0000=No repair)
Transfer user data to another Nokia phone via Infra-Red
To check weather your SIM Card supports clock stopping type- *#746025625#
(*#SIM0CLOCK#) Revealing the Headphone and Car-Kit menus Please note that if you
do these next tricks, the new menus can't be erased without retoring the factory default
settings. To do these tricks you need to short-circuit the pins on the bottom of the phone
next to where you plug in you charger.
1. To activate the "Headset" menu, you need to short-circuit pins "3" and "4". After a
short time the word "Headset" will be shown in the display. Menu 3-6 is now enabled.
2. To activate the "Car" menu, you need to short-circuit pins "4" and "5". After a short
time the word "Car" will be shown in the display. Menu 3-7 is now enabled.
THE REBOOT TRICK
This should work on all software versions of the 6110.
1. Go to the Calendar (Menu-8)
2. Make a note or reminder.
3. Enter some text into the edit box.
4. Hold "Clear" until the whole text is cleared, then press "Back".
5. Press "0". The main screen will now be showing but a space appears on the screen.
(you can't see it)
6. Enter 4 digits (e.g. 1234).
7. Use the down arrow to move the cursor to the left side of the numbers and the space
(Down arrow twice).
8. Now enter 6 digits and press the call button.
Wait for a few seconds, the screen should start to flash and reboots. It should alsowork on
other menus like the "Profiles" menu.
EFR CALL QUALITY
To activate EFR (Enhanced Full Rate) Enter the code- *3370# This improves call quality
but decreases batterylife by about 5% To deactivate it, Enter the code- #3370#
THE JAMES BOND TRICK
If you short-circuit theleft middle and right pins on the bottom of the phone with all
connections touching each other, the Nokia software hangs! The profile "Headset" will be
activated. Before you do this just activate the "Automatic Answer" in the headset profile
and set the ringing volume to "Mute". Now you can use your phone for checking out
what people are talking about in a room. Just place it under a table in a room and call it.
The phone receives the call without ringing and you can listen to what people are saying.
There is a hidden menu inside your Nokia phone. If you want to activate it, you'll have to
re-program some chips inside of your phone.
Check your software version. You can only continue if you have v4.33, v4.73 or v5.24.
Take apart the phone.
De-solder the EEPROM (ATMEL AT 24C64).
Read out the data with an EEPROM programmer and save it to a file (Backup).
If you have v.33 or v4.73, change the address "03B8" from "00" to "FF".
If you have v5.24 then change the address "0378" from "00" to "FF".
Write the new data to the EEPROM and solder it back to the phone,
Power on your phone and you should have "Netmonitor" enabled.
The Network Monitor gives you the following information.
MS RX Level in DBM
Received signal quality
MS TX power level
C1 (Path loss criterion, used for cell selection and reselection). The range is -99 to 99.
RTL (Radio link timeout). Timeslot Indication of the transmitter status Information on
the Network parameters.
TMSI (Temporary Mobile Subscriber Identity).
Cell identification (Cell ID, Number of cells being used).
MCC (Mobile country code)
MCN (Mobile network code)
LAC (Location area code)